Carlson Software Forum

Posted: **Thu May 19, 2005 7:37 am**

I receive a fatal error several times a day usually when I run the field to
finish, point editing, and surface commands. Listed below is the message
from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Thu May 19, 2005 10:52 pm**

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

I receive a fatal error several times a day usually when I run the field to
finish, point editing, and surface commands. Listed below is the message
from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Mon May 23, 2005 8:11 pm**

It is happening on all drawings!

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6in4c$1iv$1@update.carlsonsw.com...

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

I receive a fatal error several times a day usually when I run the field
to finish, point editing, and surface commands. Listed below is the
message from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Mon May 23, 2005 11:14 pm**

C Medina wrote:

It is happening on all drawings!

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6in4c$1iv$1@update.carlsonsw.com...

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

This is probably an issue that needs to be explored in some detail with

some trial and error performed. Please give me a call when you get a
free minute. 800-989-5028

I receive a fatal error several times a day usually when I run the field
to finish, point editing, and surface commands. Listed below is the
message from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Mon May 23, 2005 11:48 pm**

Barkley:

Since we updated to the latest XP Pro software,the new service pack, we have
had one or two crashes a day on many different drawings, so far the recover
drawing has kept us from losing anything. It is happening on several
different machines and it is always an unhandeled exception error. Hope
this helps, I don't know if it is the same problem that Medina is having or
not. It doesn't seem to be related to any one command.

Vince Popish

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6t9t3$b0e$1@update.carlsonsw.com...

C Medina wrote:

It is happening on all drawings!

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6in4c$1iv$1@update.carlsonsw.com...

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

This is probably an issue that needs to be explored in some detail with
some trial and error performed. Please give me a call when you get a free
minute. 800-989-5028

I receive a fatal error several times a day usually when I run the field
to finish, point editing, and surface commands. Listed below is the
message from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Tue May 24, 2005 12:38 am**

Vincent Popish wrote:

Barkley:

Since we updated to the latest XP Pro software,the new service pack, we have
had one or two crashes a day on many different drawings, so far the recover
drawing has kept us from losing anything. It is happening on several
different machines and it is always an unhandeled exception error. Hope
this helps, I don't know if it is the same problem that Medina is having or
not. It doesn't seem to be related to any one command.

Vince Popish

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6t9t3$b0e$1@update.carlsonsw.com...

C Medina wrote:

It is happening on all drawings!

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6in4c$1iv$1@update.carlsonsw.com...

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

This is probably an issue that needs to be explored in some detail with
some trial and error performed. Please give me a call when you get a free
minute. 800-989-5028

What anti-virus software package are you running?

I receive a fatal error several times a day usually when I run the field
to finish, point editing, and surface commands. Listed below is the
message from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception at
3600bb50h

---------------------------
OK
---------------------------

Posted: **Tue May 24, 2005 12:43 am**

Norton anti virus on one Mcafee on the others, seems to make no difference.

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6ter9$dtt$1@update.carlsonsw.com...

Vincent Popish wrote:

Barkley:

Since we updated to the latest XP Pro software,the new service pack, we
have had one or two crashes a day on many different drawings, so far the
recover drawing has kept us from losing anything. It is happening on
several different machines and it is always an unhandeled exception
error. Hope this helps, I don't know if it is the same problem that
Medina is having or not. It doesn't seem to be related to any one
command.

Vince Popish

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6t9t3$b0e$1@update.carlsonsw.com...

C Medina wrote:

It is happening on all drawings!

"Barkley Hensley" <bhensley@carlsonsw.com> wrote in message
news:d6in4c$1iv$1@update.carlsonsw.com...

C Medina wrote:
Is this happening in all drawings or just a particular drawing?

This is probably an issue that needs to be explored in some detail with
some trial and error performed. Please give me a call when you get a
free minute. 800-989-5028

What anti-virus software package are you running?

I receive a fatal error several times a day usually when I run the
field to finish, point editing, and surface commands. Listed below is
the message from carlson 2004.

---------------------------
Carlson Software Error Aborting
---------------------------

FATAL ERROR: Unhandled Access Violation Reading 0x19999a0a Exception
at 3600bb50h

---------------------------
OK
---------------------------

Posted: **Tue May 24, 2005 3:45 pm**

"Vincent Popish" <vpop@bresnan.net> wrote...

...so far the recover
drawing has kept us from losing anything.

Sounds dangerous. I would caution you against putting too much faith in autosave or backup files. Using QSAVE often is the only way to go. Make sure ISAVEPERCENT is set to zero also.

Posted: **Wed May 25, 2005 2:19 am**

You can't qsave when the program crashes, you have to rely on the recover or
back up.

"R.K. McSwain" <rkmcswain@yahoo.com> wrote in message
news:d6v41u$rh$1@update.carlsonsw.com...
"Vincent Popish" <vpop@bresnan.net> wrote...

...so far the recover
drawing has kept us from losing anything.

Sounds dangerous. I would caution you against putting too much faith in
autosave or backup files. Using QSAVE often is the only way to go. Make sure
ISAVEPERCENT is set to zero also.

Posted: **Wed May 25, 2005 4:03 am**

"C Medina" <terrasurveys@comcast.net> wrote in message
news:d7098q$lui$1@update.carlsonsw.com...

You can't qsave when the program crashes, you have to rely on the recover
or
back up.

LOL
You missed the point.
If you QSAVE often enough, you will never need an autosave or backup file.

I have only required an autosave and/or backup file maybe once or twice in
10+ years of using AutoCAD. And that was at the beginning.

Also, NEVER answer yes to that question "AutoCAD cannot continue, do you
want to save your changes?" - 9 times out of 10, the data written to disk
will be corrupt.

Carlson Software Forum

Fatal Error

Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error

Re: Fatal Error