Drawing Inspector Problem

[JustinB]

I have Carlson Survey and Roads 2006 and when I have points drawn through
the point group manager and do a drawing inspector to list the point data it
tells me "warning drawing coordinates to not match CRD file." Why is this??
Also, Some of the symbols are not located where they are supposed to be.
They are not at the node location. Why is this?? Please answer soon!!

--
JMB

[JustinB]

I also went and checked the coordinates on the drawing compared to the
actual coordinate file and they match exactly. This is a sanitary sewer job
and I am taking shots every other day for cut sheets. In doing so every
time I upload the new points to my file I overwrite the existing crd file
and redraw the crd file back into the drawing. Could this be what is
causing the problem??
"JustinB" <jbrungard@hrico.com> wrote in message
news:dqisqn$9ra$1@update.carlsonsw.com...

I have Carlson Survey and Roads 2006 and when I have points drawn through
the point group manager and do a drawing inspector to list the point data
it tells me "warning drawing coordinates to not match CRD file." Why is
this?? Also, Some of the symbols are not located where they are supposed to
be. They are not at the node location. Why is this?? Please answer soon!!

--
JMB

[Doug Sims]

I only get this problem if I move (move command) the points in the
drawing. This can also occur if you have multiple coordinate files and
some points are not in the current file.
Be sure to use Set Coordinate File to have the most recent (if
multiples) file active, and make sure that no one is moving points
incorrectly. Other than that, I don't know.
--Doug

JustinB wrote:

I also went and checked the coordinates on the drawing compared to the
actual coordinate file and they match exactly. This is a sanitary sewer job
and I am taking shots every other day for cut sheets. In doing so every
time I upload the new points to my file I overwrite the existing crd file
and redraw the crd file back into the drawing. Could this be what is
causing the problem??
"JustinB" <jbrungard@hrico.com> wrote in message
news:dqisqn$9ra$1@update.carlsonsw.com...

I have Carlson Survey and Roads 2006 and when I have points drawn through
the point group manager and do a drawing inspector to list the point data
it tells me "warning drawing coordinates to not match CRD file." Why is
this?? Also, Some of the symbols are not located where they are supposed to
be. They are not at the node location. Why is this?? Please answer soon!!

--
JMB

[JustinB]

No I have not moved the points. This happens right after I insert new
points by using the point group manager-insert point group. And yes I have
the right crd file selected. Like I said I did an annotate-label
coordinates and checked the map coordinates with the crd file listing and
they were exact with one another. What is it??

"Doug Sims" <dougsims@simslandsurveying.com> wrote in message
news:dqj4q9$fc7$1@update.carlsonsw.com...

I only get this problem if I move (move command) the points in the drawing.
This can also occur if you have multiple coordinate files and some points
are not in the current file.
Be sure to use Set Coordinate File to have the most recent (if multiples)
file active, and make sure that no one is moving points incorrectly. Other
than that, I don't know.
--Doug

JustinB wrote:
I also went and checked the coordinates on the drawing compared to the
actual coordinate file and they match exactly. This is a sanitary sewer
job and I am taking shots every other day for cut sheets. In doing so
every time I upload the new points to my file I overwrite the existing
crd file and redraw the crd file back into the drawing. Could this be
what is causing the problem??
"JustinB" <jbrungard@hrico.com> wrote in message
news:dqisqn$9ra$1@update.carlsonsw.com...

I have Carlson Survey and Roads 2006 and when I have points drawn through
the point group manager and do a drawing inspector to list the point data
it tells me "warning drawing coordinates to not match CRD file." Why is
this?? Also, Some of the symbols are not located where they are supposed
to be. They are not at the node location. Why is this?? Please answer
soon!!

--
JMB

[C Medina]

I have the same problem when I have the point group manager insert the
points into the drawing. The points inserted through the point group
manager do not match the crd file. However if I use the draw locate command
to insert points into the drawing they come in at the correct location. It
appears to be a problem with the point group manager. I recommend that you
use the draw locate command until they fix the problem with the point group
manager.

Chris
"JustinB" <jbrungard@hrico.com> wrote in message
news:dqj6hf$gm1$1@update.carlsonsw.com...

No I have not moved the points. This happens right after I insert new
points by using the point group manager-insert point group. And yes I
have
the right crd file selected. Like I said I did an annotate-label
coordinates and checked the map coordinates with the crd file listing and
they were exact with one another. What is it??

"Doug Sims" <dougsims@simslandsurveying.com> wrote in message
news:dqj4q9$fc7$1@update.carlsonsw.com...
I only get this problem if I move (move command) the points in the
drawing. This can also occur if you have multiple coordinate files and
some points are not in the current file.
Be sure to use Set Coordinate File to have the most recent (if multiples)
file active, and make sure that no one is moving points incorrectly.
Other than that, I don't know.
--Doug

JustinB wrote:
I also went and checked the coordinates on the drawing compared to the
actual coordinate file and they match exactly. This is a sanitary sewer
job and I am taking shots every other day for cut sheets. In doing so
every time I upload the new points to my file I overwrite the existing
crd file and redraw the crd file back into the drawing. Could this be
what is causing the problem??
"JustinB" <jbrungard@hrico.com> wrote in message
news:dqisqn$9ra$1@update.carlsonsw.com...

I have Carlson Survey and Roads 2006 and when I have points drawn
through the point group manager and do a drawing inspector to list the
point data it tells me "warning drawing coordinates to not match CRD
file." Why is this?? Also, Some of the symbols are not located where
they are supposed to be. They are not at the node location. Why is
this?? Please answer soon!!

--
JMB