Carlson Software Forum

Posted: **Tue Apr 06, 2004 8:21 pm**

Hello all,

I'm using SurvCadd to figure out cut/fill quantities. As many of you know,
doing this by Triangulation is much faster and IMO much more efficient than
using a grid file. Comparing grid files at higher resolutions seems to take
hours compared to 10 minutes with Triangulation.

The downside of using triangulation is that I seemingly cannot make a
cut/fill color map.

Is there a way to make this map without comparing GRD files?

Any help would be much appreciated as I am currently chugging away at this
project.

--
Matt Timion
Earthwork Calculation Services

Posted: **Wed Dec 15, 2004 1:58 am**

Probably too late for you...too bad somebody from Carlson does not read
this board every night.

I store the differences in a TIN then contour that TIN. You will end up
with contours that represent the amount of cut or fill. I then color by
elevation, cuts in red and fills in blue. Jeremy

Posted: **Wed Dec 15, 2004 4:22 am**

Surveyor wrote:

Probably too late for you...too bad somebody from Carlson does not read
this board every night.

....or at all.

They used to though.... :-)

Posted: **Thu Dec 16, 2004 2:39 am**

R.K. McSwain wrote:

Surveyor wrote:

Probably too late for you...too bad somebody from Carlson does not
read this board every night.

...or at all.

They used to though....
R.K. Are you the one who used to check this site? I have seen your name

in quite a few discussion groups. You have been more than helpful at the
POB site. It appears that you contribute here as well. Thanks. JRL

Posted: **Thu Dec 16, 2004 8:28 am**

On 12/15/2004 3:39 PM Surveyor wrote:

R.K. Are you the one who used to check this site?

Yes. I may be the only one who still does.. :-)

I have seen your name
in quite a few discussion groups. You have been more than helpful at the
POB site.

Try to help when I can. I learned a lot from the autodesk groups years
ago (and still do today for that matter)

It appears that you contribute here as well.

True, but I've had to cut back since the check$ from Carlson stopped a
while back ;-|

Posted: **Mon Dec 20, 2004 5:09 pm**

Hey fellas,

Don't sell this newsgroup short - we check this newsgroup at least once a
week.
I reckon that others do check it without necessarily contributing.

Scrolling back about 6 months I can see at least 8-10 names.
We use this newsgroup to get ideas & understand CS & SurvCADD more.

I'd like to think that Carlson read this - but haven't seen any input for a
while??
They probably should resume their newsletters & review the newsgroup items
to generate more interest.

Regards...Stephen

"R.K. McSwain" <not@autodesk.com> wrote in message
news:cpqv98$vrl$1@update.carlsonsw.com...

On 12/15/2004 3:39 PM Surveyor wrote:

R.K. Are you the one who used to check this site?

Yes. I may be the only one who still does..

I have seen your name
in quite a few discussion groups. You have been more than helpful at the
POB site.

Try to help when I can. I learned a lot from the autodesk groups years
ago (and still do today for that matter)

It appears that you contribute here as well.

True, but I've had to cut back since the check$ from Carlson stopped a
while back ;-|

Posted: **Tue Dec 21, 2004 2:08 am**

I check the newsgroup every few days, but I have to admit there hasn't been
much going on, and any response is usually slow, but, I see 'Ol Lon had been
in here. There is some sign of life... Maybe a little pro-mo from Carlson
would get users going again?

"Stephen Rhodes" <stephen.rhodes@fyfe.com.au> wrote in message
news:cq6e13$e4e$1@update.carlsonsw.com...

Hey fellas,

Don't sell this newsgroup short - we check this newsgroup at least once a
week.
I reckon that others do check it without necessarily contributing.

Scrolling back about 6 months I can see at least 8-10 names.
We use this newsgroup to get ideas & understand CS & SurvCADD more.

I'd like to think that Carlson read this - but haven't seen any input for
a
while??
They probably should resume their newsletters & review the newsgroup items
to generate more interest.

Regards...Stephen

"R.K. McSwain" <not@autodesk.com> wrote in message
news:cpqv98$vrl$1@update.carlsonsw.com...
On 12/15/2004 3:39 PM Surveyor wrote:

R.K. Are you the one who used to check this site?

Yes. I may be the only one who still does..

I have seen your name
in quite a few discussion groups. You have been more than helpful at
the
POB site.

Try to help when I can. I learned a lot from the autodesk groups years
ago (and still do today for that matter)

It appears that you contribute here as well.

True, but I've had to cut back since the check$ from Carlson stopped a
while back ;-|

Carlson Software Forum

Cut/Fill Color Map using Volumes by Triangulation?

Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?

Re: Cut/Fill Color Map using Volumes by Triangulation?